Home>ASTM Standards>ASTM B162-2019 pdf free download

ASTM B162-2019 pdf free download

ASTM B162-2019 pdf free download.Standard Specification for Nickel Plate, Sheet, and Strip
1. Scope
1.1 This specification 2 covers rolled nickel (UNS N02200) and low-carbon nickel (UNS N02201) 3 plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro- priate safety, health, and environmental practices and deter- mine the applicability ofregulatory limitations prior to use. 1.4 This international standard was developed in accor- dance with internationally recognized principles on standard- ization established in the Decision on Principles for the Development of International Standards, Guides and Recom- mendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
4. Ordering Information
4.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory performance of material ordered under this specification. Examples of such requirements include, but are not limited to, the following: 4.1.1 Alloy—Name and UNS number. (See Table 2.) 4.1.2 ASTM Designation, including year of issue. 4.1.3 Condition. (See 6.1, 6.2, and Appendix X1.) 4.1.4 Finish. (See Appendix X1.) 4.1.5 Dimensions—Thickness, width, and length. 4.1.6 Quantity. 4.1.7 Optional Requirements: Sheet and Strip—Whether to be furnished in coil, in cut straight lengths, or in random straight lengths. Strip—Whether to be furnished with commercial slit edge, square edge, or round edge. Plate—Whether to be furnished specially flattened (see 7.7.2); also how plate is to be cut (see 7.2.1 and 7.3.2). 4.1.8 Fabrication Details—Not mandatory but helpful to the manufacturer. Welding or Brazing—Process to be employed.
7. Dimensions and Permissible Variations
7.1 Thickness and Weight: 7.1.1 Plate—For plate up to 2 in. (50.8 mm), inclusive, in thickness, the permissible variation under the specified thick- ness and permissible excess in overweight shall not exceed the amounts prescribed in Table 5. For use with Table 5, plate shall be assumed to weigh 0.321 lb/in. 3 (8.89 g/cm 3 ). 7.1.2 Plate—For plate over 2 in. (50.8 mm) in thickness, the permissible variations over the specified thickness shall not exceed the amounts prescribed in Table 6. 7.1.3 Sheet and Strip—The permissible variations in thick- ness of sheet and strip shall be as prescribed in Table 7. The thickness of strip and sheet shall be measured with the micrometer spindle 3 ⁄ 8 in. (9.5 mm) or more from either edge for material 1 in. (25.4 mm) or over in width and at any place on the strip under 1 in. in width. 7.2 Width and Diameter: 7.2.1 Plate—The permissible variations in width of rectan- gular plates and diameter of circular plates shall be as prescribed in Table 8 and Table 9. 7.2.2 Sheet and Strip—The permissible variations in width for sheet and strip shall be as prescribed in Table 10. 7.3 Length: 7.3.1 Sheet and strip of all sizes may be ordered to cut lengths, in which case a variation of 1 ⁄ 8 in. (3.2 mm) over the specified length shall be permitted. 7.3.2 Permissible variations in length of rectangular plate shall be as prescribed in Table 11. 7.4 Straightness: 7.4.1 The edgewise curvature (depth of chord) of flat sheet, strip, and plate shall not exceed 0.05 in. multiplied by the length in feet (0.04 mm multiplied by the length in centime- tres). 7.4.2 Straightness for coiled material is subject to agree- ment between the manufacturer and the purchaser. 7.5 Edges: 7.5.1 When finished edges of strip are specified in the contract or order, the following descriptions shall apply: Square-edge strip shall be supplied with finished edges, with sharp, square corners, and without bevel or rounding.

Maybe you like

Standards Tags