Home>ASTM Standards>ASTM F696-2019 pdf free download

ASTM F696-2019 pdf free download

ASTM F696-2019 pdf free download.Standard Specification for Leather Protectors for Rubber Insulating Gloves and Mittens
4. Materials
4.1 The leather for the body of the glove shall be grain cowhide, buffed grain cowhide, grain deerskin, grain pigskin, grain horsehide, or grain goatskin. Leather shall be free ofcuts, open grub holes, or brand marks although well-healed grub scars are permitted. For protectors for Class 0 and Class 00 gloves, grain sheepskin or capeskin are also acceptable. 4.1.1 The thickness of the leather in the hand portion shall not be less than 1.00 mm (0.039 in.) nor greater than 1.60 mm (0.063 in.). For protectors for Class 0 gloves, the leather must be provided in a minimum thickness of 0.58 mm (0.023 in.), with the maximum thickness being 1.2 mm (0.04 in.). For protectors for Class 00 gloves, the leather must be provided in a minimum thickness of 0.40 mm (0.016 in.) with a maximum thickness being 1.20 mm (0.047 in.). 4.2 The cuff shall be made of either leather or polymeric material or combination of both. 4.2.1 When leather is used for the cuff, it shall be of sufficient stiffness to be self-supporting with a minimum thickness of 1.2 mm (0.047 in.) and a maximum thickness of 1.78 mm (0.070 in.). 4.2.2 When polymeric material is used for cuffs, it shall have 0.51 mm (0.020 in.) minimum thickness and 1.78 mm (0.070 in.) maximum thickness, and shall be supported with fabric or equivalent to provide sufficient stiffness to be self- supporting and to prevent excessive elasticity. Cuffs may be made of one or two layers of cuff material. 4.2.3 Cuffs may also be molded in one piece of elastomeric compounds, and shall be of sufficient thickness to be self- supporting. 4.3 An adjustable drawstrap shall be made of either grain or split leather, webbing, or “shirred elastic.” It shall be a minimum of 13 mm (0.50 in.), maximum 19 mm (0.75 in.) wide. Adjustability of drawstrap shall be obtained through the use of metal or synthetic buckles, nylon rings, or Velcro fasteners, except for shirred elastic, which provides its own adjustability. 4.4 Bonded nylon, polyester, or cotton thread shall be used throughout the protector glove. When bonded nylon or poly- ester thread is used, it shall be a minimum of size 69 and maximum of size 99, with the exception that when a looper thread is used, its minimum size may be size 46. When cotton thread is used, it should be size 16, 4-ply minimum. 4.5 The top edge of leather or polymeric cuffs shall be hemmed or finished with binding.
5. Manufacture
5.1 The leather protectors covered by this specification shall be manufactured in either clute, gunn, montpelier, or one-finger mitten patterns. 5.1.1 The clute pattern shall consist of a one-piece palm including the fronts of all four fingers and thumb. The one-piece palm may include the back ofthe index finger. When the palm includes the back of the index finger, there shall be three fourchettes to form the backs and sides of the other three fingers. When the palm does not include the back of the index finger, there shall be four fourchettes to form the backs and sides ofthe four fingers. The back of the thumb shall consist of one piece of leather. 5.1.2 The gunn pattern shall be a four-finger and thumb design in which the face of the thumb, the palm, and the first (index) and fourth (little) fingers are of one piece of leather. The palm may also include the back of the index finger. When it does, the back shall be of one piece and shall include the backs ofthe second, third, and fourth fingers up to the gauntlet. When the palm does not include the back of the index finger, then the back shall be of one piece including the backs of index, third, and fourth fingers up to the gauntlet. The fronts of the second and third fingers may be of one or two pieces of leather with outseams between fingers and the palm of the hand.

Maybe you like

Categories
Standards Tags