Home>ASTM Standards>ASTM F714-13(R2019) pdf free download

ASTM F714-13(R2019) pdf free download

ASTM F714-13(R2019) pdf free download.Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
1. Scope
1.1 This specification covers polyethylene (PE) pipe made in dimensions based on outside diameters of90 mm (3.500 in.) and larger. 1.2 Three standard outside diameter sizing systems are detailed: one known as the ISO metric system, one known as the IPS system, and the other known as the DIPS system. See 5.2.5 for guidelines for special sizes. 1.3 The piping is intended for new construction and inser- tion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpres- sure systems. N OTE 1—The user should consult the manufacturer to ensure that any damage to the polyethylene pipe caused by the material being transported will not affect the service life beyond limits acceptable to the user. 1.4 All pipes produced under this specification are pressure- rated. See Appendix X5 for information on pressure rating. N OTE 2—References and material descriptions for PE2406, PE3406, PE3408 and materials having a HDB of1450 psi have been removed from Specification F714 due to changes in Specification D3350 and PPI TR-3. For removed designations, refer to previous editions of Specification F714, Specification D3350, PPI TR-3 and PPI TR-4. The removal ofthese materials does not affect pipelines that are in service. See Notes 9 and 9. 1.5 This specification includes criteria for choice of raw material, together with performance requirements and test methods for determining conformance with the requirements. 1.6 Quality-control measures are to be taken by manufac- turers. See Appendix X4 for general information on quality control. 1.7 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10) and DIPS system. In all cases, the values given in parentheses are provided for information only.1.8 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all ofthe safety concerns, ifany, associated with its use. It is the responsibility ofthe user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accor- dance with internationally recognized principles on standard- ization established in the Decision on Principles for the Development of International Standards, Guides and Recom- mendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
4. Materials
4.1 Polyethylene Compound—Polyethylene compounds suitable for use in the manufacture of pipe under this specifi- cation shall meet thermoplastic materials designation codes PE2708 or PE3608 or PE4608 or PE4710, and shall meet Table 1 requirements for PE2708 or PE3608 or PE4608 or PE4710, and shall meet thermal stability, brittleness temperature and elongation at break requirements in accordance with Specifi- cation D3350. 4.1.1 Polyethylene compounds suitable for use in the manu- facturer of DIPS pipe per Table 2 and Table 3 are identified by thermoplastic pipe material designation code, and shall be PE4710 or PE3608 in accordance with 4.1, 4.1.2 and 4.2. 4.1.2 Color and Ultraviolet (UV) Stabilization—Per Table 1, polyethylene compounds shall meet Specification D3350code C or E. In addition, Code C polyethylene com- pounds shall have 2 to 3 percent carbon black, and Code E polyethylene compounds shall have sufficient UV stabilizer to protect pipe from deleterious UV exposure effects during unprotected outdoor shipping and storage for at least eighteen (18) months. 4.2 Potable Water Requirement—When required by the regulatory authority having jurisdiction, products intended for contact with potable water shall be evaluated, tested, and certified for conformance with NSF/ANSI Standard No. 61 or the health effects portion of NSF/ANSI Standard No. 14 by an acceptable certifying organization. 4.3 Rework Material—Clean polyethylene compound from the manufacturer’s own pipe production that met 4.1 through 4.1.2 as new compound is suitable for reextrusion into pipe, when blended with new compound of the same thermoplastic pipe material designation code. Pipe containing rework mate- rial shall meet the requirements of this specification.

Maybe you like

Standards Tags